Pro-face America - STC6000 Series

Unit of Measure

Items	PFXSTC6300TADDKE 5.7" HMI plus Control	PFXSTC6300TADDCE 5.7" HMI plus Control
Type	N/A TFT Color LCD (VGA)
Size	N/A 5.7"
Colors	N/A 262,144
Resolution	N/A 640 x 480 pixels
Brightness Adjustment	N/A 16 levels of adjustment available via touch panel in the Configuration menu
Backlight	N/A White LED adjustable on/off control
Area	N/A 95.04 x 53.86 mm (3.74 x 2.12 in)	N/A 115.2 x 86.4 mm (4.54 x 3.40 in)
Touch Panel	N/A Resistive Film (Analog) 1024 x 1024 pixels
Backup	N/A Uses a part of Flash EPROM as the backup area. (Maximum usable capacity*1: 392 KB)
System	N/A Flash EPROM 1 GB (operating system, project data and other data)
Serial (COM1)	N/A RS-232C/422/485
Ethernet	N/A IEEE802.3i/IEEE802.3u, 10BASE-T/100BASE-TX, Modular jack (RJ-45) x 1
USB	N/A USB 2.0 (Type A) x 1 , USB 2.0 (micro-B) x 1
CANOpen	N/A Reserved
Built in DIO (Input)	N/A 24 Vdc open collector. Single phase (4-point) 2 phase (1-point or 2-point)
Built in DIO (Output)	N/A 4 points
Clock	N/A Battery backed clock.
Rated Voltage	N/A 24 Vdc
Rated Voltage Range	N/A 20.4 Vdc to 28.8 Vdc
Power Consumption	N/A Max 11.3 W
Minimal Ambiant Operating Temperature	N/A 0 ºC32 ºF
Maximal Ambiant Operating Temperature	N/A 50 ºC122 ºF
Storage Temperature	N/A -20 to 60 ºC-4 to 140 ºF
Dust	N/A 0.1 mg/m3 (10-7 oz/ft3) or less (non-conductive levels)
Pollution Degree	N/A For use in Pollution Degree 2 environment.
Corrosive Gases	N/A Free of corrosive gases
Vibration & Shock Resistance	N/A IEC/EN 61131-2 compliant, 5...9 Hz Single amplitude 3.5 mm (0.14 in) 9...150 Hz Fixed acceleration: 9.8 m/s2 X, Y, Z directions for 10 cycles (approximately 100 minutes)
Shock Resistance	N/A IEC/EN 61131-2 compliant 147 m/s2, X, Y, Z directions for 3 times
Ratings¹	N/A IP65F, UL 50/50E, Type 1, Type 4X (indoor use only), Type 12 and Type 13 (on the front panel when properly installed in an enclosure)
Certifications	N/A UL 61010-2-201 and CSA C22.2 N°61010-2-201, for Industrial Control Equipment used in Ordinary Locations, Underwriters Laboratories Inc., UL 121201 and CSA C22.2 N°213, for Industrial Control Equipment used in Class I, Division 2 Hazardous (Classified) Loc
Cooling method	N/A Natural Air Circulation
External Length	N/A 6.67 in169.5 mm
External Depth	N/A 2.36 in60 mm
External Height	N/A 5.39 in137 mm
Panel Cut Length	N/A 6.14 in156 mm
Panel Cut Height	N/A 4.86 in123.5 mm
Panel Thickness Area²	N/A 0.06 to 0.2 in1.6 to 5 mm
Warranty	N/A 18 Month Standard
Weight	N/A 0.8 kg1.76 lb
Power	N/A DC
Address	N/A Proface America, 1050 Highland Drive, Suite D, Ann Arbor, MI, 48108, 734-477-0600
Supported Software	N/A GP-Pro EX
Communications	N/A Ethernet USB
Screen Type	N/A Wide TFT Color LCD
Handheld Configuration	N/A No
¹ The front face of this product, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though this product's level of resistance is equivalent to these standards, oils that should have no effect on this product can possibly harm this product. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to this product for long periods of time. If this product's front face protection sheet or cover glass peels off, these conditions can lead to the ingress of oil into this product and separate protection measures are suggested. Also, if non-approved oils are present, they may cause deformation or corrosion of the front panel's cover. Therefore, prior to installing this product, be sure to confirm the type of conditions that will be present in this product's operating environment. If the installation gasket is used for a long period of time, or if this product and its gasket are removed from the panel, the original level of protection cannot be kept. To maintain the original protection level, be sure to replace the installation gasket regularly. ² Even if the installation wall thickness is within the recommended range for the Panel Cut Dimensions, depending on the wall's material, size, and installation. location of this product and other devices, the installation wall could warp. To prevent warping, the installation surface may need to be strengthened.(R0.12 in).